操一操-操一操干一干-操一操日一日-操一操影院-操伊人

+86-755-23595309

Runic’s products apply in Finger clip oximeter

2022-01-27
Page View:1862
Source:

The Household portable Finger clip oximeter is highly flexible ,can quickly measure the percentage of human blood oxygen saturation (SpO2 ) and pulse rate on the basis of non-injury.Has won wide and high praise and has sold well continuously.

?

As the Hemoglobin in blood has different absorb ability of red light and infrared light.Compare the Hemoglobin? with oxygen (HBO2) and the Deoxygenated hemoglobin(HB) ,HB absorbs more red light and less infrared light, HBO2, on the other hand, absorbs less red light and more infrared. The Red and infrared leds are next to each other in Structurally,thus can allow light pass through in the finger pointed single position conveniently.Light travels from one side of the finger to the other side, after picked up by a photodiode and produce a proportional voltage to it.

?

Runic as a High- tech company with high performance analog signal chain design capabilities, our product line such as OP Amps, Comparator,? Analog Switch, LDO,etc. Can? match very well with the design of? consumer medical products such as? Finger clip oximeter.

?

The typical schematic block diagram of portable Finger clip oximeter is as below:

77.png

In the picture above,the Analog switch RS2105 of Runic is used to switch red LED and infrared LED lamps,they are time-sharing and modulate at a certain frequency. The OP Amp RS321 works with the DAC inside in the MCU to produce a constant current output signal, because the constant-current operation of LED lamp can obtain a relatively stable wavelength, the emission current usually reaches tens of mA, so the on-resistance of analog switch should be less than 1Ω, and the on-resistance of our RS2105 is 0.6Ω, which meets the application requirement well.

?

On the side of the photosensitive receiver, the OP Amp RS622 is used for the photoelectric conversion, which requires the input bias current Ib of the OP Amp to be pA-level, and the?bandwidth of the OP Amp needs to be more than 5 MHZ to satisfy the fast response.The low noise series OP Amp can better to improve the resolution of the system. In the power topology, one is to use two cell dry batteries(3V) boost to 5V and then buck to the system circuit to use, the other is use lithium battery,which can be cycle charged for use.Our low power consumption LDO RS3236 are suitable for both topologies.

?

The main parameters of Runic’s low noise OP Amp RS622 are as below:

?

Wide voltage supply range: 2.5V~5.5V;

?

Low offset voltage:? 0.7mV typical,? 3mVmax;

?

Low temp shift: 2uV/°C typical;

?

Low input bias current IB:1pA;

?

Gain Bandwidth: 7MHz;

?

Quiescent current: 600uA per channel;

?

Noise factor:11nV/√Hz.

?

The main parameters of Runic’s Analog switch RS2105 are as below:

?

Wide voltage supply range: 1.8V~5.5V;

?

Low on-resistance:? 0.6Ω,? 1Ω max;

?

Output current continues:500mA;

?

-3dB Bandwidth30MHz;

?

Quiescent current: less than 1uA;

?

Has MSOP-10TDFN-3*3-10L package for your choice.

?

The main parameters of Runic’s low consumption LDO RS3236 are as below:

?

Wide input voltage range: 1.7V~7.5V, support 4 cells dry battery input application;

?

Internal max output current limit: >500mA;

?

Ultra-low quiescent current: 20uA;

?

Ultra-low drop voltage :1mV/mA;

?

Ultra-high PSRR: 70dB/Hz;

?

Output voltage density optional: 1% or 2.5%;

?

Kinds of fixed -output voltage and many packages such as SOT-23, SOT-89-3, SOT-23-5, UTDFN-1*1-4L for your choice.


主站蜘蛛池模板: 成人www| 国产福利专区| 国产黄大片在线观看视频| 免费亚洲网站| 在线看国产| 2020久久精品永久免费| 国产乱码在线精品可播放| 国产成人精品日本| 亚洲国产精品a一区二区三区| a在线观看免费| 欧美成人精品第一区二区三区| 新香蕉视频| 欧美性三三影院| 日韩欧美一区二区久久| 日韩欧美国产亚洲| 精品国产品香蕉在线观看75| 欧美视频在线免费播放| 日韩免费一级毛片| 欧美在线成人午夜网站| 视频久久精品| 成人午夜大片免费看爽爽爽| a级片免费在线观看| 久久午夜网| 草草在线视频| 古代的一a一片一级一片| 亚洲综合亚洲| 国产日韩欧美亚洲青青草原| 国产欧美自拍| 毛片毛片毛片| 日韩亚州| 国产精品久久久久一区二区| 中文字幕一区视频一线| 午夜特片网| 奥田咲在线播放| 在线欧美成人| 亚洲成人第一| 黄色短视频免费| 污污美女网站| 91热爆在线精品| 国产婷婷丁香久久综合| 国产97视频|